Cement transporter saves on tyres and time with AES workshop solutions

Share on facebook
Share on twitter
Share on linkedin

Cris Services Group, the Purfleet-based concrete haulier and commercial repairs specialist, has reduced workshop costs, extended tyre life and cut vehicle downtime since acquiring a Josam wheel alignment system and portable heat inductor from Pontefract, West Yorkshire-based AES UK.

With 40 vehicles carrying wet cement for Hanson UK and a mixed fleet of concrete mixer trucks for hire, Cris Services were keen to improve workshop efficiency and to drive down operation costs such as tyre replacement and fuel.

“The equipment we invested in from AES,” says Transport Manager Alin Gabor, “provided the solution for two key challenges: preventing tyre wear caused by mis-aligned wheels and dealing with lengthy workshop procedures when coping with seized nuts and bolts etc.” 

The Cam-aligner is a compact digital wheel alignment system which according to Alin, enables Cris Services to carry out on-the-spot checks and rectifications without the need to book into a third party. 

“The equipment is fully portable and uses advanced camera technology to establish the true chassis centre line of the vehicle. With only a half turn of the wheel, it determines any toe, camber and out- of-square measurements.” 

Wireless technology then transmits the data from the calibration equipment to the computer and a clear diagram on screen shows exactly where the issues lie and what corrective action needs to be taken.

“All done in a fraction of the time taken by less advanced systems” continues Alin Gabor, “and more thorough too. It saves a great deal of time for our HGV, PSV and LCV customers during servicing, maintenance and repairs, and also within our own fleet when preparing vehicles for MOT. Plus, our customers can expect a full report and analysis, which is printed out after each job.  It’s a good piece of kit and perfect for preventing potential handling problems and tyre wear before it occurs.” 

According to Cris Services, the Josam Cam-aligner is saving so much in terms of tyre wear, labour and fuel, that it is likely to pay for itself within the first year – an assessment which, the company says, is also likely to be the case with the AES HI 3.5 heat inductor, supplied at the same time under a year ago.

“The heat inductor is quite simply a Godsend.” Says Alin. “This little piece of equipment scores high in terms of safety, while enabling us to speed up routine maintenance and repair work such as seized up ball joints, chassis screws, casings and wheel nuts. Using gas, we would often have to cut away the seized component, which meant first removing any flammable materials or electrics that could be affected by the heat.”

The AES HI 3.5 however, uses electrically generated heat, which means the operator and workplace are not exposed to open flame, hot gases and the risk of fire or explosion. Furthermore, the system is lightweight and water-cooled.

“These two pieces of equipment have certainly gone a long way to improve the quality and value of the service we provide to our customers,” concludes Alin Gabor. “At at the same time, they have proved to be a major commercial benefit for our own haulage operation.” 

With its main offices and operation based in London, Cris Services Group also covers areas such as Kent, Sussex, Essex, Hertfordshire and Berkshire. The company is FORS-accredited, an FTA member and is an authorised service agent for Stetter.

Established in 2005 and based in Pontefract, AES is the UK’s sole distributor of Josam products, providing commercial vehicle alignment and CV workshop equipment, along with on-site training, servicing and equipment calibration to truck, bus and van operators throughout the UK. 

Automotive Equipment Solutions (AES), is a provider of commercial vehicle alignment equipment, with nearly 40 years’ experience in the automotive industry. The company provides a wide range of garage and workshop equipment and training on a nationwide basis. a-e-s-uk.co.uk

FIND OUT MORE: AES UK is exhibiting at the ITT Hub 2021 event on June 30-July 1, at Farnborough International, just off the M25, west of London. Register for your free place now! www.itthub.co.uk

You will receive our regular news digest – typically weekly. We are serious about GDPR and we promise to take care of your data and will never sell it or pass it on.

Your Privacy

We and our partners use technologies, such as cookies, and process personal data, such as IP addresses and cookie identifiers, to personalise ads and content based on your interests, measure the performance of ads and content, and derive insights about the audiences who saw ads and content. Click below to consent to the use of this technology and the processing of your personal data for these purposes. View our privacy policy.